> Gasoline Engine > DR Gasoline Fuel Filter / Regulator / Pump
Dodge Ram truck Please visit Geno's Garage for truck accessories
Geno's garage Truck Acessories

 Gasoline Fuel Filter / Regulator / Pump   (DR Ram Truck)


49.2 psi +/- 2 psi (339 kPa +/- 34 kPa).

The fuel pump module assembly is located on the top of the fuel tank. The complete assembly contains the following components:

The fuel gauge sending unit may be serviced separately. If the electrical fuel pump, primary inlet filter, fuel filter or fuel pressure regulator require service, the entire fuel pump module must be replaced (until there is an aftermarket source for individual component parts).

Fuel Filter:
All gasoline engines have a fuel strainer inside the fuel tank at the bottom of the fuel pump's pickup. There is also a combination fuel filter and fuel pressure regulator located on the top of the fuel pump module. A separate frame or engine mounted fuel filter is not used with any engine. Both fuel filters (at bottom of fuel pump module and within fuel pressure regulator) are designed for extended service and do not require normal scheduled maintenance unless a diagnostic procedure indicates that one or both of these filters require service.


Fuel Pressure Regulator Operation:
The pressure regulator is a mechanical device containing a diaphragm, calibrated springs and a fuel return
valve. The regulator is not controlled by engine vacuum or the Powertrain Control Module (PCM), and it is calibrated to maintain fuel system operating pressure of approximately 49.2 psi ± 5 psi (339 kPa ± 34 kPa) at the fuel injectors. If fuel pressure at the pressure regulator exceeds 49.2 psi, an internal diaphragm opens and excess fuel is returned the tank through the bottom of pressure regulator. A separate fuel return line
from the engine to the tank is not used. The internal fuel filter is also part of the assembly.
To help when starting the engine, the regulator acts as a check valve to maintain some fuel pressure while the engine is off. Fuel is supplied to the filter/regulator by the electric fuel pump inside the fuel tank below the filter/regulator. A second check valve is located at the the electric fuel pump outlet.

Fuel Gauge:
The fuel gauge sending unit is attached to the side of the fuel pump module. The sending unit consists of a float, an arm, and a variable resistor. The PCM supplies constant current to the variable resistor and monitors the voltage drop accross the resistor. Using this voltage returned from the fuel level sensor, the PCM calculates the fuel level and supplies the level as digital information to the instrument panel for the fuel gauge.

The fuel pump module has 4 different circuits (wires). Two of these circuits are used for the fuel gauge sending unit for fuel gauge operation, and for certain OBD II emission requirements. The other 2 wires are used for electric fuel pump operation. from fuel pump module.
For diagnostic purposes, the 12V constant current source can only be verified with the circuit opened (fuel pump module electrical connector unplugged). With the connectors attached, fuel level output voltages will vary from about 0.6 volts at FULL, to about 7.0 volts at EMPTY. The variable resistor track is used to vary the voltage (resistance) depending on fuel tank float level. As fuel level increases, the float and arm move up, which decreases voltage. As fuel level decreases, the float and arm move down, which increases voltage. The varied voltage signal is returned back to the PCM through the sensor return circuit.

Fuel level and OBDII diagnostic codes:
If the fuel level is less than approximately 15 percent of the tank capacity, the OBD II system will not record/set a misfire code. The Leak Detection Pump EVAP system monitor (if equipped) will be activated if the fuel level in the tank is more than approximately 85 percent of tank capacity.

Fuel Pump:
The electric fuel pump is located inside the fuel pump module, which installs though the top of the fuel tank. A 12 volt, permanent magnet, electric motor powers the fuel pump. Voltage to operate the electric pump is supplied through the fuel pump relay. Fuel is drawn in through a filter at the bottom of the module and pushed through the electric motor gearset to the pump outlet.
The bottom section of the fuel pump module contains a one-way check valve to prevent fuel flow back into the tank. When pump is not running, this check valve maintains fuel supply line pressure when the engine is warm, and keeps the fuel supply line full of gasoline. After the vehicle has cooled down, fuel pressure may drop to 0 psi  as the gasoline cools and contracts, but liquid gasoline will remain in fuel supply line between the check valve and fuel injectors. Fuel pressure that has dropped to 0 psi on a cooled down vehicle (engine off) is a normal condition.

The electric fuel pump is not a separate, serviceable component. See the Service Manual for fuel system component removal and replacement instructions.


CAUTION: The interior components (o-rings, spacers) of some types of quick-connect fitting are not serviced separately. If service parts are not available, do not attempt to repair a damaged fitting or fuel line. If repair is necessary, replace complete fuel line assembly.

  Top of Page Home  


This page was edited on: May 3, 2004